Page 1 of 1

4mm locomotive lining - transfers?

Posted: Tue Jan 29, 2013 1:43 pm
by lawman
Having (slowly) been constructing a layout & stock, I'm rapidly approaching that stage where I'll need to start lining locomotives. I've lined a 439 tank using white/black/white waterslide transfers from Fox but ideally need to find something suitable for black locomotives. I've found straight & curved individual red & white transfers on their website but don't know if these will be suitable for lining of wheelsplashers. Knowing my present limitations with a lining pen, does anyone out there know of a source of suitable transfers?
I had thought of asking one of the transfer suppliers if they would be able to make something as I don't have a suitable printer for a DIY attempt - if so, would there be any demand to have a batch of transfers made up and the costs shared?

Iain

Re: 4mm locomotive lining - transfers?

Posted: Tue Jan 29, 2013 1:54 pm
by jasp
Hi
What scale are you working in?
If 4mm, I would be interested
Jim P

Re: 4mm locomotive lining - transfers?

Posted: Tue Jan 29, 2013 6:06 pm
by BillAuld
Have you tried Modelmaster Decals, they have a website. Only problem is if you use the BR mixed traffic lining and reverse it you hit problems with the reverse curves. It would be OK for straight lines though.
They also do nice white/black/white lining sold as LNER.

Re: 4mm locomotive lining - transfers?

Posted: Tue Jan 29, 2013 7:52 pm
by John Lindsay
I have a similar problem. I am half way through lining a black Jumbo in 4mm. I am reasonably happy with the straight lines using HRMC press fix separate red and white lining, although both are a bit thick and the red too dominant. I suspect it will be ok with a bit of weathering. I filled in the corners with a small paint brush. I tried the BR mixed traffic red and grey, but felt the red dominated even more as the 'white' is grey.

I did the boiler bands using white backed crafty computer printer transfer paper with black and red lines printed on it and then trimmed very close to get the outer white line. I used a simple inkjet printer and then put on three coats of acrylic varnish as the instructions recommend.

I have now got to the splashers. I have tried the HRMS LNER loco lining red curves which, whilst much finer than the straight lines, fit well. (In retrospect, perhaps the LNER black loco fine red lining would have been better for the straight lines too.) I have now paused while I think about the white. Any suggestions would be welcome!

I found the Modelmaster LNER white and black lining good for my first blue loco, but a bit thick. I think the company has said it is going to stop printing this product soon, but it is still on the website.

John

Re: 4mm locomotive lining - transfers?

Posted: Wed Jan 30, 2013 8:48 am
by JimG
John,

Have you thought about printing a transfer for the whole splasher? I only raise this since I have been thinking ahead to the problem (for me!!) of painting and lining locomotives and I have been thinking of generating larger transfers to include the colour of the locomotive for difficult areas like splashers and cab sides - this to cut down on the disguising of the transfer base.

JimG.

Re: 4mm locomotive lining - transfers?

Posted: Fri Feb 01, 2013 9:34 pm
by John Lindsay
Jim

I have fiddled about with shapes in Word this evening trying out a whole splasher approach as you suggested. It looks quite promising at the moment. I will let you know how I get on when I try printing on the white backed transfer paper.

John

Re: 4mm locomotive lining - transfers?

Posted: Sat Feb 09, 2013 5:18 pm
by Dave John
I have tried various methods over the years and have never been totally happy with any of them. If a manufacturer did produce a CR lining sheet I would be a customer.

Re: 4mm locomotive lining - transfers?

Posted: Thu Apr 11, 2013 6:19 pm
by John Lindsay
A quick update.

I tried printing the lining for the splashers on my black Jumbo on crafty computer transfer paper with some success.

It was a bit of a compromise. I found that following the recommendations of the manufacturer and using the normal print setting on my inkjet printer gave a black that was not dense enough. Changing the setting to photo quality gave a much better Black, but the ink trends to spread a little and the red line was thinner as a result. I also used a little too much varnish, but that worked out ok.

I didn't attempt to line the sand box under the smoke box in this way; instead I used straight line transfers and a bit of free hand for the curves.

I am reasonably pleased with the result and might work up the confidence to post a picture!

Cheers

John